EP2C5T144C8N DATASHEET PDF

EP2C5TC8N from Altera Corporation. Find the PDF Datasheet, Specifications and Distributor Information. EP2C5TC8N IC CYCLONE II FPGA 5K TQFP Altera datasheet pdf data sheet FREE from Datasheet (data sheet) search for integrated. Device Family Data Sheet. This section provides information for board layout designers to successfully layout their boards for Cyclone™ II.

Author: Brashura Dok
Country: Cuba
Language: English (Spanish)
Genre: Travel
Published (Last): 14 February 2015
Pages: 182
PDF File Size: 14.62 Mb
ePub File Size: 11.84 Mb
ISBN: 742-7-67034-532-9
Downloads: 57806
Price: Free* [*Free Regsitration Required]
Uploader: Nerr

Revision History Refer to each chapter for its own specific revision history. For information on when each chapter was updated, refer to the Chapter Revision Dates section, which appears in the complete handbook.

Altera Corporation Section I. Cyclone II Architecture Chapter 3. Reference designs, system diagrams, and IP, found at www. The EP2C5A is only available in the automotive datasyeet grade.

Altera Corporation February — — — — — — — — A programmable register A carry chain connection A register chain connection The ability to drive all types of interconnects: LUT for unrelated functions. When using register packing, the LAB-wide synchronous load control signal is not available.

LEs in normal mode support packed registers and register feedback. The Altera Corporation February Register feedback and register packing are supported when LEs are used in arithmetic mode. Figure 2—5 Figure 2—5.

The LE directly supports an asynchronous clear function. Each LAB supports up to two asynchronous clear signals labclr1 and labclr2. These row resources include: Driving Left Notes to Figure 2—8: Cyclone II Device Handbook, Volume 1 Register chain interconnects within an LAB C4 interconnects traversing a distance of four blocks and down direction C16 interconnects for high-speed vertical routing through the device Figure 2—9 shows the register chain interconnects. Altera Corporation February For LAB interconnection, a primary Epc25t144c8n or its LAB neighbor see interconnects can drive each other to extend their range as well as drive row interconnects for column-to-column connections.

Table 2—1 Table 2—1. DPCLK[] pins are dual-purpose clock pins. There are four clock control blocks on each side.

Figures 2—11 and 2— The following sources can be inputs to a given clock control block: Internal logic ep2c5h144c8n be used to enabled or disabled the global clock network in user mode. IN Altera Corporation February IOE clocks are associated with row or column block regions. Only six global clock resources feed to these row and column regions.

The signal enables and disables the PLLs. The pfdena signal controls the phase frequency detector PFD output with a programmable gate. If the C2 output is not Altera Corporation February The M4K memory blocks include ep2c5t144c8b registers that synchronize Memory writes and output registers to pipeline designs and improve system performance. The output registers can be bypassed, but input datasbeet cannot.

  INTRODUCERE IN GEOPOLITICA PDF

This applies to both read and write operations. Altera Corporation February summarizes the features supported by the M4K memory.

Simultaneous read and write from an empty FIFO buffer is not supported. Description Altera Corporation February M4K block outputs can also connect to left and right LABs through each 16 direct link interconnects. Altera Corporation February summarizes the different clock modes supported by the M4K Description In this mode, a separate clock is available for each port ports A and B The total number of multipliers for each device is not the sum of all the multipliers.

The embedded multiplier consists of the following elements: Multiplier Modes Table 2—12 multipliers can operate in. R4 Interconnects Embedded Multiplier Control 36 [ The Quartus II software automatically duplicates a single OE register that controls multiple output or bidirectional pins.

EP2C5TC8N Intel Altera | Ciiva

You can use IOEs as input, output, or bidirectional pins. There are two paths available for combinational or registered inputs to the logic array. Each path contains a unique programmable delay chain. All registers share sclr and aclr, but each register can individually disable sclr and aclr. Programmable delays decrease input-pin-to-logic-array and IOE input register delays.

The Quartus II Compiler can program these delays to automatically minimize setup time while providing a zero hold time. The system clock is used to clock the DQS write signals, commands, and addresses. Figure 2—27 the dedicated circuitry to the logic array. Number of LVDS Channels 1 31 35 56 60 61 65 29 33 53 57 75 79 52 60 45 53 52 60 Altera Corporation February This also minimizes the need for external resistors in high pin count ball grid array BGA packages.

When using on-chip series termination, programmable drive strength is not available.

Cyclone II Device Family Data Sheet

A device operating in JTAG mode uses four required pins: File via an embedded processor. Manufacturer Identity 11 Bits and 3—3 show the 1, 1, 1, LSB 1 Bit Altera Corporation February Cyclone II devices are configured at system power-up with data stored in an Altera configuration device or provided by a system controller. The datasheft CCIO selects whether the configuration inputs are 1. The ep2c5t144d8n feature in Cyclone II devices offers the following: This condition can lead to latch-up and cause a low-impedance path from V a large amount of current, possibly causing electrical damage.

  ALESSANDRA ROSALDO OPEN PDF

CC parameters will determine the initialization time. February Removed ESD section. Altera Corporation February ramp time requirement, you must CC shows the revision history for dataheet document.

Cyclone II EP2C5 Mini Dev Board – blwiki

Additionally, device operation at the absolute maximum ratings for extended periods of time may have adverse effect on the device reliability. During transition, the inputs may undershoot to —2. This value is specified for normal device operation.

The value may vary during power-up. This applies for all V settings 3. V ICM 3 The p — n waveform is a function of the positive channel p and the negative channel n. Capacitance is sample-tested only.

Capacitance is measured using time-domain reflectometry TDR. Refer to typical I standby specifications. Timing Specifications You should select power supplies and regulators that can supply the amount of current required when designing with Cyclone II devices.

EP2C5T144C8N

The second row represents the minimum timing parameter for commercial devices. Speed —8 Speed Grade Unit Grade 2 0. Speed —8 Speed Unit Grade Grade 2. These numbers are for automotive devices. Peak-to-peak output jitter on high-speed PLLs. Lock time for high-speed transmitter and receiver PLLs. Refer to Figure 5—4 CO Figure 5—5. Ep2v5t144c8n extended temperature devices, the maximum data rate for x1 mode is Mbps.

DCD for a clock is the datashfet value of D1 and D2. Duty Cycle Distortion DCD expressed in ep2c51t44c8n derivation, for example Figure percentage, and the percentage number is clock-period dependent. DCD as a percentage is defined as: Therefore, any distortion on the input Figure 5—9. For more information contact Altera Applications. Ordering Figure 6—1 information on a specific package, contact Altera Applications Elcodis is a trademark of Dtaasheet Company Ltd.

All other trademarks are the property of their respective owners. Download datasheet 3Mb Share this page. Copy your embed code and put on your site: Prev Next This section provides information for board layout designers to. Refer to each chapter for its own specific revision history. DC Characteristics and Timing Specifications. Automotive-Grade Altera Corporation February —