DIN IEC – DRAFT. Draft Document – Switched protective earth portable residual current devices (SPE-PRCD) for class I and battery. IEC Edition INTERNATIONAL. STANDARD. NORME. INTERNATIONALE. Circuit breakers – Switched protective earth. Buy IEC Ed. Circuit breakers – Switched protective earth portable residual current devices for class I and battery powered vehicle applications from .
|Genre:||Health and Food|
|Published (Last):||28 July 2012|
|PDF File Size:||6.19 Mb|
|ePub File Size:||14.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
For example, it specifies mechanisms such that, first, power is not supplied unless a vehicle is connected and, second, the vehicle is immobilized while still connected.
Dimensional compatibility and interchangeability requirements for a. Dimensional compatibility and interchangeability requirements for d.
All connectors can be converted with passive or simple adapters, although possibly 6235 with all charging modes intact.
The following standards are incorporated as connector types:. IEC is applicable to plugs, socket-outlets, connectors, inlets and cable assemblies for electric vehicles, intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding:.
The connection does not ie extra control pins. In some countries including the USA, Mode 1 charging is prohibited. One problem is that the required earthing is not present in all domestic installations.
Mode 2 was developed as a workaround for this. A number of plug types are under consideration for DC charging. The Japanese Chademo plugs have been in use for a number of years uec while the common plug type is considered too bulky. This connector is the current de facto standard in Japan.
Tesla is using modified Type 2 plug for SuperCharger. This modified connector allows for deeper insertion, and longer conductor pins, allowing for greater current. The connectors standardised in IEC are specialized for automotive use. The lack of a latch also puts unnecessary strain on any locking mechanism.
Also the Scame plugin is ied by a French-Italian alliance mentioning its comparable low price. In iex second phase expected to be and latera uniform connector shall be used only, whereas the ultimate choice for Type 2 or Type 3 is left open. While the first ACEA position paper June has ruled out the Type 1 connector based on the requirement of three-phase charging which is abundant in Europe and China but not in Japan and the USA it has left open the question whether a Type 2 or Type 3 connector should be used for the uniform plug type in Europe.
The shutter protection of Type 3 connectors do only have advantages in Mode 2 lec for a simpler charging station. On the other hand, a public charging station exposes the charging socket and plugs to a harsh environment where the shutter could easily have a malfunction which is not noticeable to the electric vehicle driver.
Instead 62353 ACEA expects that Type 2 Mode 3 connectors also to be used for home charging in the second phase after while still allowing Mode 2 charging with established plug types that are already available in home environments. The EV Plug Alliance had proposed two connectors with shutters.
IEC Standard – Exhibition – BESEN-Group
The Italian standardization body CEI tested the Mennekes shutter proposal where Italy is a country requiring mechanical shutters and in May the Italian and German partners approved it as a compromise solution for Type 2 to be included in the CENELEC standardization of electric vehicle charging connectors.
In Octoberit became known that Schneider a founding member of ieec EV Plug Alliance only manufactures charging stations with Type 2S connectors Type 2 with shutters. All plug types of IEC have the two additional signals: The proximity pilot or, plug presence signal allows the EV to detect when it is plugged in.
This allows the EV to inhibit movement while a charging cable is attached, and to cease charging as the plug is disconnected, so there is no load and associated arcing.
Again, inside the plug itself, a passive resistance is connected across PP and PE. The cable can 622335 further indicate its current rating to the EVSE with different resistances.
IEC | IEC Webstore
The control pilot signal is designed to be easily processed by analog electronics, eliding the use of digital electronics, which can be unreliable in automotive settings. The resistance in the EV can be manipulated by 623335 in a resistor in parallel with always connected 2. Besen,leading the EV charging to a better way! General requirements IEC Part 2: The following standards are incorporated as connector types: Charging modes IEC is applicable to plugs, socket-outlets, connectors, inlets and cable assemblies for electric vehicles, intended for use in conductive charging systems which incorporate control means, 622335 a rated operating voltage not exceeding: Related Industry Knowledge Electric vehicle charging station b Electric vehicle charging station s Important considerations for EV cha Electric vehicle charging plug design Functional requirements for electri Safety requirements for electric ve Adaptability analysis of electric c Performance of electric car chargin Using characteristics of car chargi Electric vehicle charging cable gro Please update this article to reflect jec events or newly available information.