ISO 7823-1 PDF

Standards for PLEXIGLAS® GS DIN EN ISO Plastics – Poly(methyl methacrylate) sheets. Types, dimensions and characteristics. Part 1: Cast sheets. without any technical changes the International Standard: ISO “ Plastics – Poly(methyl methacrylate) sheets – Types, dimensions. Plastics – Poly(methyl methacrylate) sheets – Types, dimensions and characteristics – Part 1: Cast sheets (ISO ); German version.

Author: Arashilmaran Samujinn
Country: Belize
Language: English (Spanish)
Genre: Career
Published (Last): 9 July 2014
Pages: 272
PDF File Size: 17.49 Mb
ePub File Size: 2.52 Mb
ISBN: 937-3-36972-956-5
Downloads: 24064
Price: Free* [*Free Regsitration Required]
Uploader: Kishicage

ISO – Inmetro. ISO – Inmetro Aug 15, This PDF file may contain embedded typefaces. In accordance with Adobe’s licensing policy, this file may ISO – Inmetro Mar 15, ISO – Inmetro Sep 4, Guide 33 — Uses of CRMs Guide 32 — Calibration Using Ensaio de alongamento a frio. Texto principal da monografia do qual podem fazer parte alguns ou todos BS EN definition of steel product.

IEC, Safety of lamp controlgear — Part In accordance with Adobe’s licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing.

In downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing.

Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.

The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.


International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.

NF EN ISO – Tests – CSTB Evaluation

This fourth edition cancels and replaces the third edition ISO The sheets may be colourless or coloured, and may be transparent, translucent or opaque. The thickness range of the sheets covered by this part of ISO is 1,5 mm to 25 mm.

For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document 7823- any amendments applies.

BS EN ISO 7823-1:2003

General test method ISO Plastics, ebonite and long-fibre-reinforced composites ISO Non-instrumented impact test ISO General principles 1 To be published.

Revision of ISO Test conditions for moulding and extrusion plastics ISO Immersion method, liquid 78823-1 method and titration method ISO Density gradient column method ISO Rockwell hardness ISO Xenon-arc sources ISO Open-flame carbonarc lamps ISO Determination of coefficient of linear thermal expansion and glass transition temperature ISO Single-beam instrument ISO Double-beam instrument ISO Revision in parts of ISO National environmental legislation and regulations shall be followed regarding additives.

There shall be no scratches, marks or other surface defects larger than 3 mm2 each anywhere in the sheet. Each defect shall be considered separately. Table 1 — Classification of defects 5. What constitutes a significant number shall be agreed between the interested parties. Variations in colour shall be agreed upon between the interested parties.

For cut sheets, the tolerances for each sheet shall be as specified in Table 2. The tolerances apply within each sheet and from sheet to sheet. For measurements made under ambient conditions, due allowance shall be made for dimensional changes due to the differences in temperature and relative humidity between test locations. Examples of, and test methods for, such properties are presented in Table 4. The sampling procedure given in ISO is widely accepted and frequently used. Hence it is recommended.


When it is necessary to 7283-1 the sheet to the thickness required for a particular test method, one original surface shall isso left intact.

Measurements shall be carried out at not less than mm from the sheet edge. The original surface shall be put under tension whenever the specimen has been machined to the specified dimensions. The pendulum shall strike the surface that is opposite to the original one if the specimen has been machined to the specified dimensions.

Measurements shall not be carried out on isso with a thickness below 3 mm. Flammability The flammability and burning properties shall be determined in accordance with national fire regulations.

By agreement between the interested parties, the light transmittance may alternatively be determined oso exposure to a carbon-arc lamp see ISO Changes in colour and properties after exposure shall be determined in accordance with ISO The details of these tests shall be agreed upon between the interested parties. For the purposes of on-line quality control testing, this drying stage may be omitted, but in cases of dispute it is required.

Mark the four sides and measure the length of each to the nearest 0,02 mm. Take suitable precautions to avoid the specimens sticking to the plate: The heating time, which depends on the thickness of the sheet, shall be as given in Table A.

Then sprinkle a light covering of talc isl the specimen, place a second aluminium sheet over the specimen jso spacer, and fasten the two aluminium sheets together lightly with clips. Calculate the average percentage change for the four sides of each specimen and the average value for the set of three specimens.

PBE Veicular – Inmetro.

Aditivos para radiadores – Inmetro. Lighting sio – Inmetro. Remember me Forgot password? COM To ensure the functioning of the site, we use cookies. We share information about your activities on the site with our partners and Google partners: Your consent to our cookies if you continue to use this website.